What Are Hexagonal Bars and What Are They Used For
Try holding a round bar still with a spanner and you will soon find the problem: there are no flats to grip, so the tool slips. That small frustration is exactly what hexagonal bar solves, because its six flat faces give a spanner, a socket or a chuck something solid to hold and give you something to measure.
For hobbyist machinists, engineers and DIY fabricators, hex bar stock is one of the most practical pieces of engineering bar to keep to hand, but only if you know when its shape helps. Before looking at where it is used, it is worth understanding what sets the six-sided profile apart, as this helps explain its popularity.
What Is Hexagonal Bar Stock and How Does It Differ from Round and Square Bar?
Hexagonal bar stock is metal formed into a six-sided section, with every face flat and every corner meeting the next at the same 120-degree angle. That regular shape is what separates it from round bar, which has no flat surface for a spanner or clamp to bite on, so it can slip when force is applied.
Because every face is flat, it can be held securely in a vice or chuck. Square bar does offer flats, but a spanner can only be repositioned every 90 degrees, and its sharper corners are more easily knocked or rounded off with repeated use. The six-sided bar profile sits between the two, with the flats that give a firm hold and a wider angle that lets a tool be moved in smaller steps, which helps in tight spaces. Once you can see why that balance matters, it becomes easier to understand where the shape earns its keep.
What Is a Hexagonal Bar Used For?
The answer follows from that balance of firm hold and easy tool access, because hex bar stock suits any job where a part must be gripped, turned or tightened. In practice, the most common uses fall into four groups:
- Shafts and Spindles: A hexagonal drive end lets a coupling or handle transmit torque without slipping, which makes the section a dependable choice for a short shaft.
- Fasteners and Nuts: Bolts, studs and custom nuts are often turned from hex material, because a finished fastener already carries the flats that a spanner needs.
- Tooling and Handles: Hexagonal ends fit chucks, sockets and drivers, so bespoke tool bits, adaptors and knobs are straightforward to make on a lathe.
- Furniture and Fabrication: The flats give clean, geometric lines for legs, rails and brackets, and they provide a flat surface for fixing or welding.
How Hexagonal Bar Is Made and Sized for Precision Work
Every one of those uses depends on the bar being accurate, which is why it helps to know how it is produced. Hex bar stock is commonly supplied either hot rolled or cold drawn, and the cold drawn route pulls the metal through a die at room temperature, giving tighter dimensional control and a smoother surface. Material finished this way is often described as bright bar, a term you will see used for precision work where a clean, consistent finish matters.
Size is quoted across flats, meaning the distance between two opposite faces, and this is also the measurement a spanner or socket will match. The distance from corner to corner is around 15% wider, so it is worth checking which figure a drawing or supplier is quoting before you order. Once you are clear on size and finish, the remaining choice is which metal suits the job.
Choosing Between Stainless Steel, Aluminium and Brass Hex Bar
With size and finish settled, the metal you choose decides how your hex bar stock behaves once you start work on it. Each option has a clear role:
- Stainless Steel: Stainless steel hex bar is strong, highly resistant to corrosion and well suited to fasteners, shafts and parts used outdoors, although it is tougher to machine than brass or aluminium.
- Aluminium: Aluminium hex bar weighs roughly a third as much as steel and resists corrosion naturally, which suits lightweight fixtures, handles and parts that are handled often.
- Brass: Brass hex bar is a favourite for turning because it machines cleanly and holds fine detail, and it looks attractive on visible parts such as knobs and fittings.
If you are unsure which metal is right for your project, our team can help, and a quick conversation before ordering is often all it takes to get the choice right.
Cut-to-Size Hexagonal Bar from Click Metal
Once you have chosen your material, the next step is getting it in the length your project needs, and this is where Click Metal can help. We cut hex bar stock to your required length as standard, with a general cutting tolerance of + or - 2mm, so there is no extra trimming once it arrives and very little waste.
Everything is processed on site from stock held under an ISO-accredited stockholding system that has been in operation since 1994, and we aim to process and despatch most orders within 48 hours by national courier. There is no minimum order charge, so one short length is as straightforward to order as a larger batch, whether you are making a single prototype or a run of parts.
And if your project calls for bulk quantities or a specialist grade, our parent company, Doré Metal Services, can support larger requirements.
Getting Your Hex Bar Cut to the Length You Need
A six-sided profile earns its place wherever a part needs to be gripped, turned or tightened, and the right finish, size and metal make all the difference. If you can't find the exact size you need in the shop, call our team on 01794 526090 or send your requirements through our contact form, and we will do our best to sort it.
Choose the profile that does the job, and we will cut it to fit.
Find the right metal for your project.
Choose your material, select your size and we will cut it to your requirements.